Fresh Start Fitness Equipment
595 Broad Hollow Rd. Farmingdale NY 11735
Ph: 631 420 0008 Fx: 631 420 4966
FSFE REMANUFACTURING PROCESS
➤ Treadmill Remanufacturing Process:
The treadmill is taken apart and receives a new running belt, Deck, hardware, and motor bearings.
It also receives resurfaced rollers. The frame is professionally painted/ powder coated with stock
or custom colors. Once the treadmill is put back together it will be cleaned and polished finally.
The treadmill is tested and shipped.
- New heart rate grips
- Clean and detailed all plastic shrouds and caps with acrylic finish, replace if cracked or damaged
- New belt
- Re-surface rollers in our custom built
- New decals throughout machine
- Install new deck with new shock absorption system
- Update software in the console
- New overlay/keypad and new iPod connector kit
- Sand and repaint frame with 2 stage base and high gloss clear
- New drive belt, new high speed rubber-sealed bearing installed in motor
➤ Ellipticals Remanufacturing Process:
The elliptical is taken apart and receives new drive belts, hardware ramps, wheels and incline track assembly,
and console housing/overlay as needed. Once the elliptical is put back together, it will be cleaned, polished
and painted/powder coated finally. The elliptical is tested and shipped.
- Replace front arm grips
- Install new wave washers, hardware and snap rings
- Clean and polish all covers
- New decals throughout machine
- Grease, oil and lubricate all necessary components
- New ramp inserts and sleeves
- Install primary and secondary drive belts
- Sand entire frame, arms and repaint with a two stage base and high gloss clear coat
- Diagnostics test on all electronics
➤ Bikes and Stationary Bikes Remanufacturing Process:
The bike is taken apart and receives a new chain, drive belt, and hardware/clips. Once the bike is put back together, it will be cleaned and polished and painted/powder-coated. The bike is tested and shipped
- Diagnostics test on all electronics
- Replace keypad and overlay
- Replace any cracked or damaged plastics or repaint in acrylic satin finish
- Install new crank arm assembly and bearings
- Install new pedals with straps
- New primary and secondary drive belt
- Install new 6V rechargeable battery
- Clean and lubricate all foot levelers
- Clean and polish all covers
- Install new wave washers, hardware and snap rings
- Sand entire frame, arms and repaint with a two stage base and high gloss clear coat
- Replace any worn or damaged components (e.g. seat, arm rests)
➤ Stair Steppers Remanufacturing Process:
The stepper is taken apart and receives a new chain, drive belt, hardware and non-skidtape as needed. Once the stepper is put back together, the stepper will be cleaned and polished and powder-coated finally. The stepper is tested and shipped.
- Sand frame down & repaint in textured black factory finish
- Rebuild clutch assembly
- Install new step chains on both sides
- Install new battery
- Install new transmission chain
- New pedal arm bushings
- Install new pedal hardware, washers and snap rings
- Diagnostics test on all electronics
➤ Strength Equipment Remanufacturing Process:
The strength machine is taken apart. The frame is sanded down to the bare metal. Then a powder coat of your color choice is applied. Pulleys, hardware and decals are installed as needed. The seat padding is reupholstered. The strength machine is tested and shipped out
- New decals throughout the machine
- Shrouds are replaced if damaged
- Weight stack is repainted and stickers are replaced
- Frame is sanded down and repainted/powder coated
- Upholstery is replaced with choice of any of our custom colors
- All hardware, bushings, bearings and grips are tested and replaced
- Belt (or cable) is replaced and tightened
Current Openings
Data Analyst / BI Analyst – E-Commerce
Technology / E-Commerce • New York, NY • Full-time